No. 32(32) (1981): Electrical engineering and electrical equipment

Automated Electromechanical Systems

• Investigation of the stability of electric drives with a pulse-width driver on the AVM.

  В. А. Скороходов

  3-6

  Abstract views: 86 |
• The calculation of the electromechanical characteristics of the system pulse-width converter - the engine.

  Л. А. Шпиглер

  6-9

  Abstract views: 206 |
• Transistor pulse-width frequency converter.

  А. Б. Гудзенко

  9-14

  Abstract views: 124 |
• External characteristics of compensated static converters in autonomous electrical systems.

  В. С. Петрушин

  15-19

  Abstract views: 267 |
• Boundary modes of the armature circuit of a low-power thyristor electric drive with a shunt diode.

  А. Ф. Синолицый

  19-24

  Abstract views: 95 |
• Features of modeling the electric drive rack pusher furnace furnace.

  В. Г. Боровик, А. М. Корытин

  24-28

  Abstract views: 187 |
• Control of multi-motor electric multi-roller tensioning mechanisms.

  Л. Г. Лимонов

  28-36

  Abstract views: 276 |
• Optimization on the CVM of the parameters of a two-channel drive for the installation of rolls with harmonic effect.

  Б. И. Кузнецов

  36-40

  Abstract views: 271 |
• Selection of an asynchronous electric drive system using an electronic computer.

  Р. П. Герасимяк, Н. С. Путилин

  40-44

  Abstract views: 280 |
• Physical and mathematical modeling of asynchronous electric drives with thyristor switches in the stator circuit.

  И. И. Печковский

  45-49

  Abstract views: 157 |
• Features of the dynamics of self-excitation mode of single-phase machines.

  Н. Л. Дорохольский, В. Н. Невольниченко

  49-55

  Abstract views: 234 |
• On the issue of improving the accuracy of the thyristor voltage regulator control system.

  Г. В. Антонов

  55-58

  Abstract views: 85 |
• Intermediate amplifier for electric drives with a wide range of speed control.

  А. А. Прокопенко, В. И. Коржов

  58-61

  Abstract views: 105 |
• Synthesis of adaptive control systems for electric gear hobbing machines.

  В. А. Елисеев, Ю. И. Богачев, В. Н. Ладик, Н. А. Горманюк

  62-68

  Abstract views: 100 |
• Graph-analytical method for determining the economical mode of operation of the biropositive shaft generator.

  Л. В. Вишневский

  68-74

  Abstract views: 278 |
• Pulse meter engine speed.

  В. Л. Сердюк, М. М. Нетипанная

  74-76

  Abstract views: 111 |
• Voltage ripple in DC tachogenerators with magnetic armature asymmetry.

  Ю. В. Осидач, В. В. Попичко

  76-83

  Abstract views: 155 |
• The choice of the design expression of the specific magnetic conductivity of the air gap of an induction motor, taking into account the steel saturation.

  Ю. А. Шумилов, В. К. Петровский, Е. В. Струневич

  83-87

  Abstract views: 122 |
• Combined three-phase windings with the ratio of the numbers of poles 2p₁: 2p₂ = 2: 8.

  В. Д. Лущик, З. В. Калинина

  87-90

  Abstract views: 77 |
• Switching overvoltages when switching on and switching failures of bulk windings of asynchronous motors.

  Н. А. Реуцкий, К. Н. Вакуленко

  90-95

  Abstract views: 113 |
• Determination of the overheating of the DC motor windings using the orthogonal scheduling method.

  В. А. Яковенко, Н. А. Осташевский, Б. В. Клименко, В. Д. Юхимчук

  95-97

  Abstract views: 391 |
• Some directions of increasing the unit capacity of transformers for DC power transmission.

  Г. В. Пуйло, В. М. Суханов, В. С. Курбатов, В. П. Чайковский

  98-102

  Abstract views: 480 |